Kerr effect Totally Explained

Everything about Kerr Effect totally explained

ť This page is about the Kerr nonlinear optical effect. For the magneto-optic phenomenon of the same name, see magneto-optic Kerr effect.

The Kerr effect or the quadratic electro-optic effect (QEO effect) is a change in the refractive index of a material in response to an electric field. It is distinct from the Pockels effect in that the induced index change is directly proportional to the square of the electric field instead of to the magnitude of the field. All materials show a Kerr effect, but certain liquids display the effect more strongly than other materials do. The Kerr effect was found in 1875 by John Kerr, a Scottish physicist.
Two special cases of the Kerr effect are normally considered: the Kerr electro-optic effect, or DC Kerr effect, and the optical Kerr effect, or AC Kerr effect.

Kerr electro-optic effect

The Kerr electro-optic effect, or DC Kerr effect, is the special case in which the electric field is a slowly varying external field applied by, for instance, a voltage on electrodes across the material. Under the influence of the applied field, the material becomes birefringent, with different indexes of refraction for light polarized parallel to or perpendicular to the applied field. The difference in index of refraction, Δn, is given by ť

Delta n = lambda K E^2,

where λ is the wavelength of the light, K is the Kerr constant, and E is the amplitude of the electric field. This difference in index of refraction causes the material to act like a waveplate when light is incident on it in a direction perpendicular to the electric field. If the material is placed between two "crossed" (perpendicular) linear polarizers, no light will be transmitted when the electric field is turned off, while nearly all of the light will be transmitted for some optimum value of the electric field. Higher values of the Kerr constant allow complete transmission to be achieved with a smaller applied electric field.
Some polar liquids, such as nitrotoluene (C₇H₇NO₂) and nitrobenzene (C₆H₅NO₂) exhibit very large Kerr constants. A glass cell filled with one of these liquids is called a Kerr cell. These are frequently used to modulate light, since the Kerr effect responds very quickly to changes in electric field. Light can be modulated with these devices at frequencies as high as 10 GHz. Because the Kerr effect is relatively weak, a typical Kerr cell may require voltages as high as 30 kV to achieve complete transparency. This is in contrast to Pockels cells, which can operate at much lower voltages. Another disadvantage of Kerr cells is that the best available material, nitrobenzene, is poisonous. Some transparent crystals have also been used for Kerr modulation, although they've smaller Kerr constants.

Optical Kerr effect

The optical Kerr effect, or AC Kerr effect is the case in which the electric field is due to the light itself. This causes a variation in index of refraction which is proportional to the local irradiance of the light. This refractive index variation is responsible for the nonlinear optical effects of self-focusing and self-phase modulation, and is the basis for Kerr-lens modelocking. This effect only becomes significant with very intense beams such as those from lasers.

Magneto-optic Kerr effect

The magneto-optic Kerr effect (MOKE) is the phenomenon that the light reflected from a magnetized material has a slightly rotated plane of polarization. It is similar to the Faraday effect where the plane of polarization of the transmitted light is rotated.

Theory

DC Kerr effect

For a nonlinear material, the electric polarization field P will depend on the electric field E:
ť

mathbf|^2 = n_0 + n_2 I

where n₂ is the second-order nonlinear refractive index, and I is the intensity of the wave. The refractive index change is thus proportional to the intensity of the light travelling through the medium.
   The values of n₂ are relatively small for most materials, on the order of 10^-20 m² W^-1 for typical glasses. Therefore beam intensities (irradiances) on the order of 1 GW cm^-2 (such as those produced by lasers) are necessary to produce significant variations in refractive index via the AC Kerr effect.
   The optical Kerr effect manifests itself temporally as self-phase modulation, a self-induced phase- and frequency-shift of a pulse of light as it travels through a medium. This process, along with dispersion, can produce optical solitons.
   Spatially, an intense beam of light in a medium will produce a change in the medium's refractive index that mimics the transverse intensity pattern of the beam. For example, a Gaussian beam results in a Gaussian refractive index profile, similar to that of a gradient-index lens. This causes the beam to focus itself, a phenomenon known as self-focusing.

Further Information

Get more info on 'Kerr Effect'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://kerr_effect.totallyexplained.com">Kerr effect Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.